Satin Ribbon Flowers

The use of satin ribbons in needlework allows you to create beautiful and spectacular crafts. Original flower satin compositions will delight with a magnificent view, with proper care they will not lose their attractiveness and, unlike fresh cut ones, will never fade.

Making different kinds of flowers does not require a lot of material. Consumption is very economical. It is enough to master several simple techniques performed by technicians in order to create original and beautiful decorations from ordinary satin ribbons.

Satin Ribbon Poinsettia

Satin Ribbon Poinsettia

To create a snow-white spectacular flower take:

  • ribbons green and white;
  • sequins;
  • half beads;
  • felt;
  • scissors;
  • glue gun;
  • lighter.

Step-by-step instruction

Pattern sheets and petals

Green ribboncut into strips approximately 6-7 cm long. Oblong leaves are cut out of the resulting segments. The wavy edges and high tensile properties of the atlas gives "burning" over the fire. Each piece is taken with tweezers and burned with a flame from a lighter.

Pattern sheets and petals

To give the leaves naturalness, they are bent in half to obtain a characteristic bend. When they are ready, each is held over a lighter flame.

White Satin Ribboncut into 10 strips. One half is made by 7, and the second - by 5 cm. Five larger and five smaller petals are cut out of the segments. As in the case of leaves, the edges are burned.

Flower assembly

Flower assembly

The basis for the decoration is a circle of felt. Leaves are fixed on it by means of a glue gun, and petals are glued on top. The center of the composition is decorated with sequins, semi-beads. You can use any other decoration.

Poinsettia is ready!

Create Satin Rose

Create Satin Rose

The technique of making roses is similar to the previous one. Materials take the same, except that the rose can be made in different shades, not just white.

Step-by-step instruction

Creating a template

Work on the flower start with creating a sketch for the petals. His draw on a piece of paper in the cell. Templates make two. One should be more than the other half a centimeter.

Pattern of petals

  1. Larger patternimpose on the ribbon for cutting six petals. To speed up the process and make all the elements absolutely identical, the tape is folded several times before. Do not use pins.They can leave traces on the atlas. For fixing it is better to take the usual clips for paper.
  2. Smaller paper patternalso applied to the tape. It should make the same number of petals, that is, six.
  3. Pattern reducefor six more, but the smallest petals.

The result should be six large, medium and small petals.

If the edges of the satin elements turned out uneven, do not worry. These flaws will easily fix the burning. You can use both a cigarette lighter and a candle.

Roasting

Satin petals hold over the flame until the edges begin to melt. To make them wavy, the tape is slightly pulled, giving the necessary shape.

For convenience, it is recommended to use tweezers to keep the material at a distance from the fire while working with it with your hands When the petals take shape, they are removed from the flame so that the material does not catch fire.

Roasting

Rose assembly

Petals are arranged both round and staggered. It all depends on the ideas and personal preferences of the craftswoman. Folded elements sew. When the first row of petals is stitched, stamens are inserted and fixed in the middle. Sew the remaining petals and get a fully formed flower.

Rose assembly

Leaves

Form of green satin ribbon. It is enough to take 10 cm. The ends of the strip are burned. This avoids disintegration of the material. The corners of the segment are folded to the center, getting a kind of "triangle" rounded from above, stitched to the bottom with a basting seam.

The thread is tied until the tips connect together. Stitched edges of the tape are stitched with a seam. It turns out a lush and beautiful piece. The number of leaves depends on the overall composition. Most often for roses make a pair.

Leaves

Rose formation

On a round felt base with hot glue, first glue the sheets, and then the rose. This rose can be a great brooch. To this end, you only need to glue the pin to the back of the felt.

Rose formation

Original ideas and recommendations

There are many variations of creating spectacular and beautiful colors from ribbons of various widths. In the decoration of hats and bags look best large crafts.

They are made from strips cut to about 12 cm, which are ground together and then folded in half. The strip obtained from the stitched pieces is twisted round. To keep the composition, each coil quilted.You can also twist a rosette from a narrow ribbon. One edge of the segment stitch basting stitches, and then tighten. The tape is wound in a circle, fixed with stitches.

Flowers, in the creation of which more than one technique was used, look particularly impressive. It can be a combination of roses made in different ways. Scorched petals make it possible to get a rose-like rose, which is perfectly complemented by a small rosette glued to the center on the cone. A lot of great ideas can be emphasized from the video, show imagination and create something of your own.

Satin flowers in kanzashi technique

Original and great kanzashi- These are spectacular decorative flowers, which until recently were used exclusively as jewelry for Japanese kimonos. Today they have become a popular decor for clothes, bags, used as an accessory for wedding hairstyles or at the prom.

The kanzashi technique is a method of producing colors that resembles modular origami. Because of this, the flowers can be given the most diverse shape and size. The basic modules of technology include rounded and pointed petals.

Satin flowers in kanzashi technique

Initially, kanzashi was made of natural silk, and the elements were glued with rice glue. Today, these materials have been replaced by others. Atlas is especially popular. Modules can be connected by hot glue or "Moment".

Creating a hyacinth in kanzashi technique

  1. Using blue tape, perform from five to six petals, using the kanzashi technique. They are strung on a needle to stretch a thread through the petals. The knot on the end is not tied. It will serve to insert into the center of stamens.

  1. To keep the stamens secure, they are smeared with glue and then placed in the center. Thread tighten, tie a knot. The result of the work done becomes an elongated blue hyacinth. If you make several of these flowers, you can collect a whole bunch.

  1. Separately perform the leaves, which are fixed in the area of ​​the sepal, giving the hyacinth a complete look.
  2. At the final stage, the buds are formed and the hoop, hairpin or other accessory is decorated with them.

To get neat kanzashi blanks from the first time is difficult. This technique requires a certain skill. The more you practice, the better the "modules" will be.And for the flowers to be truly magnificent, you need to train.

Related news

Satin Ribbon Flowers image, picture
Satin Ribbon Flowers 56


Satin Ribbon Flowers 38


Satin Ribbon Flowers 4


Satin Ribbon Flowers 28


Satin Ribbon Flowers 19